Skip to content

OpenCreator CFW Full Feature Set

Finished works on a printer   Semi-Finished partly done   Testing in testing or untested   Broken not working yet

Feature Implementation Description
ZMax on Print End Finished Puts the bed to the very bottom of the build area, for easy grabbing, a suggestion from @josemyab
Allow for near zero purge printing Finished You can turn off purge and flow calibration to have almost zero purge on start, a half suggestion from @josemyab
Purge line toggle Testing The purge line in front of the print has its own purge_line switch (on by default), separate from the bucket purge; see How to toggle features.
Chamber heats with the bed (Pro Only) Testing Print start turns the chamber heater on together with the bed, without waiting for it, using the chamber temperature from the slicer's filament settings.
Allow for calibration of only one toolhead Finished You don't need to calibrate all offsets to update z-offset of a nozzle, for switching nozzles.
Saved baby stepping per tool Testing Baby stepping Z during a print is saved to that tool's Z offset, so the next print starts from it. LIST_BABYSTEP shows each tool's value and CLEAR_BABYSTEP TOOL= resets one or all; see Baby stepping.
Allow for configuration of nozzle calibration Finished If your nozzle doesn't fit the min mm for levelboard, you can set it higher.
Filament runout and switchover support Untested Give a tool a backup in AFC ("Infinite Spool") and a runout switches to it by itself, with the run-out tool's Tx commands sent to the backup. With no backup, it pauses and asks: switch to another loaded tool, or load new filament.
AFC Toolchanger Finished Allows for the use of AFC filament system, but with toolchangers. Should be fully functional except for "loaded" filament buttons.
GrumpyScreen Toolchanger Support Semi-Finished GrumpyScreen now properly shows all extruders and currently in use extruder, but you cannot extrude yet.
Stock Feature Parity Finished Should have feature parity.
Every FlashForge firmware version Finished Installs on any FlashForge release, 1.7.8 up to the latest 2.0.0 (kernel 2.0.8), with no need to update or downgrade first. See Supported FlashForge firmware.
Full WebUI support Finished You can avoid using the touchscreen, and don't even need it in general.
SFTP over SSH Finished Transfer and manage files over SSH using SFTP, unlike stock firmware, which requires SCP for file transfers.
SSH login banner Testing Logging in over SSH shows the OpenCreator logo with the uptime, IP address, free space, installed plugins and printer model, and a coloured prompt that shows the current folder; see Login banner.
Plugins Testing Add-ons with their own Klipper modules, macros, Moonraker components and background programs, installed with oc-plugin from a catalog of official and unofficial plugins or any git URL. Plugins say which printers they're made for, and their logs are kept in check; see Plugins.
Automatic Fan control for Heated Chamber (Pro Only) Finished Removes user fan control, and makes it automatically turn on when the chamber is set to something.
Make Camera Better / Faster Finished Uses pre-installed MJPEG streamer over stock camera control in the touchscreen executable, making it efficient and fast.
Input shaper graphs Finished CALIBRATE_INPUT_SHAPER_GRAPH calibrates input shaper and draws Klipper's frequency response graph for each axis on the printer itself, no PC needed; see Input shaper graphs.
Timelapse Finished Moonraker Timelapse records a frame per layer from the printer camera and renders the video when the print ends; see Timelapse. Installed by the OpenCreator Installer.
VDS filament dryer (SoC) Finished Start, stop and pause FlashForge's two-chamber dryer from Fluidd or macros, with each chamber graphed as a temperature sensor; see Filament dryer.
Allow to switch toolheads arbitraily Finished You can send commands T0-T3 or click the buttons to pick up the toolheads.
Allow to load multiple toolheads simultaneously Finished You can send the load command for multiple tools, which changes them, loads, then docks.
Allow for reading colour information and material information on Orca Finished OrcaSlicer syncs the filament list from the printer like an AMS: material and colour for every tool. Needs a current OrcaSlicer development build.
ACE Pro auto feed and auto load Finished Each ACE slot feeds its own head. A new spool is fed to the head's filament sensor by itself, and pressing load takes it into the gears and purges. Feeds made during a print wait until it ends.
ACE Pro multiplexing Planned Several ACE slots feeding one head, in the planning stages.
Raspberry Pi Host support Finished Allowing to use a Raspberry Pi over the stock MIPS32 CPU, by tunneling the MCUs through the SoC through gadget mode USBs.
Power Loss Recovery Finished Allows to resume a print from power loss or MCU errors. The resumed print keeps its bed mesh, layer count, print time and estimates. Until you resume or discard it, the bed is kept at the print's temperature so the part stays stuck down; discarding turns the heaters off.
Kalico Support Finished On all installs, you install Kalico, a beefed up Klipper fork with features such as MPC tuning.
Removal of FlashForge services Finished You can completely disable FlashForge's things, and make it like it never existed. Full Orcaslicer with Moonraker Agent.
Filament sync Finished Syncs your filaments (material and colour) into OrcaSlicer. Needs a current OrcaSlicer development build; older releases had a bug that broke it.
Turn off cooling fan when chamber heater is on Finished It will actively say in console that it has been turned off, making it where cold air won't mess with the heated chamber
Bed warp stabilization (bed soak) Finished Optionally waits at bed temperature for a configurable number of minutes immediately before a fresh mesh, letting the plate finish warping/expanding so the mesh reflects its settled shape instead of its heat-up transient. Skipped when the bed target is below 45 °C.
Chamber heat wait toggle Finished Controls whether M191 blocks until the chamber actually reaches target, or just sets the target and lets the print start heating in the background while early layers print (M141-like). Toggle with C5_MISC_CHAMBER_WAIT_ON / OFF.
OpenCreator Updater Finished A dedicated Moonraker update_manager entry that merges the latest config template into your live printer_data/config without clobbering values you've customized (speeds, toggle defaults, etc), then pulls Klipper -- all from one "Update" click. Uses a real three-way merge, so a conflicting change is left for you to resolve by hand instead of guessed at or silently overwritten. SoC/LoopScript installs get an equivalent boot-time version, not yet verified on real hardware.
First-time setup dialog In development After installing, Fluidd, Mainsail and the screen walk you through pressure advance calibration, purging, Clog Detection and bed heat soak, point out the calibrations worth running (VFA on the printer; offsets, input shaper and VFA on an SBC), then point you to the Discord. Input shaper and PID come from FlashForge's calibration, imported on a first install. Shown until finished once; C5_FIRST_SETUP shows it again.
3MF uploads Finished Upload a sliced .gcode.3mf from OrcaSlicer or Bambu Studio straight to Fluidd or from the slicer; the first sliced plate is extracted with its thumbnail. SBC installs.
OpenCreator Fluidd theme Finished An extra-dark Fluidd theme with the OpenCreator logo. Installed and updated with the config.
Updater self-repair Untested repair.sh fixes "No git repo detected" in the update manager: starts git where it is missing, syncs to the official main branch, fixes moonraker.conf.
Door open notification Finished With C5_MISC_DOOR_NOTIFY_ON (or the door_notify switch in Fans & Outputs), opening the top or front door during a print, or starting a print with one open, shows an error pop-up in Fluidd and Mainsail and beeps (unless quiet mode is on). Uncomment [notifier door_open] in moonraker.conf to also get it on your phone. C5_DOORS shows whether each door is open.
Chamber fan follows the heater Finished The chamber heater fan turns off as soon as the chamber heater's target is cleared, instead of running until the chamber cools below 50 °C.
Chamber heater fan full speed toggle (Pro Only) Finished The chamber heater fan normally slows to half speed once the chamber is near its target. Turn on chamber_heat_fan_full in Fans & Outputs (or C5_MISC_CHAMBER_HEAT_FAN_FULL_ON / OFF) to keep it at 90% whenever the chamber heater is on. The setting survives restarts.
Wi-Fi beep fallback Finished (Pi-tunnel) If a board is pinned to 4 tunnel ports (no dedicated beep serial channel), C5_BUZZER can fall back to sending the beep request over the network to the tunnel bridge instead of silently going quiet. Opt-in via network_host in [creator5_remote_beeper].
Quieter motors Testing The mainboard follows the real move between steps and cancels each X/Y motor's own wobble, calibrated with RIPPLE_CALIBRATE. Up to 40–60% less toolhead vibration at printing speeds; see Quieter motors. Needs the phase-stepping mainboard firmware.
Quieter board fans Finished The mainboard and power supply fans ramp with the board's temperature and the power supply's load instead of running at full speed whenever the printer is busy; see Mainboard and power supply fans.
MCU temperatures Finished The mainboard and toolhead board chips' temperatures show in Fluidd and Mainsail; see MCU temperatures.
Motion guard Testing Skipped step and stall detection for X, Y and Z, off by default; see Motion guard.
VDS Support Finished VDS Support is available, but untested as no one on the development team owns a VDS or plans on owning a VDS.