Skip to content

Status and roadmap

OpenCreator is a work in progress. The table shows what's in the code and how well it has been tested on a printer.

Area Present in development source Current evidence and remaining work
Four MCU ports Mainboard, eBoard, heaterboard, and levelboard support is under development in kalico. Finished and open for new features.
Kalico MCU port Creator 5 MCU support has been ported to Kalico, and a four-board development archive was structurally validated from commit e48df776. Same as above.
Klipper host on printer Creator 5 modules, MCU protocol support, and printer configs exist. It is working.
Toolchanging and AFC standalone T0 to T3 motion, physical dock and grab checks, filament mapping, runout integration, and safety interlocks are implemented. Mostly finished testing, and should almost be 100%.
Print start and stop Four-tool preparation, optional flow and purge, bed mesh, nozzle Z checks, and normal EOF stop are implemented. All sequences are working as intended
Flow and VFA calibration The host has an eboard pressure-advance test and MCLib vibration calibration integration. It mostly works, but may still have some bugs if the flow is interrupted.
Touchscreen and web UI Mainsail/Fluidd controls and separate touchscreen. GrumpyScreen has had multi-extruder pulled in, macros are in dev.
Complete removal of firmwareExe The main pain point for FlashForge printers Their bad touchscreen + camera + print uploading sequence has been completely removed and do not function at all.
Installer Touchscreen installer from a USB drive: Entware, LoopScript, Kalico, Moonraker, Mainsail/Fluidd, GrumpyScreen, the root login and MCU firmware flashing, with a backup first (optional) and restore. Recovery and Update Configs when it's already installed. Working: tested from a fully stock install to a OpenCreator install.
OpenCreator Updater A Moonraker update_manager entry (Pi-tunnel installs) that 3-way-merges the latest config template into your live config without clobbering customized values, then pulls Klipper -- one "Update" click. SoC installs get an equivalent LoopScript-triggered version. Verified live on a real Pi + printer, conflicts no longer ever touch the live file, only a sibling .conflict file. SoC also works.
Real Zero Purge modes Implemented into switches You can turn off Flow Calibration and Purging to make a basically zero waste printer. It prints a small purge line to prime the nozzle when starting the print, but thats it. It is under runout in Fluidd, or Misc in Mainsail.
Print Farm / Automation support Ready Works with anything that just uses Moonraker. You should be able to just plop in any file and it should be able to just take it.
RPI Support In testing Currently being tested, but allowing to tunnel the board MCUs to a Raspberry Pi. High quality cables are required or else you will get strange results.
ACE Pro Working Each ACE slot feeds its own head (slot 1 to T0 ... slot 4 to T3). Auto feed takes a new spool to the head's filament sensor, and auto load takes it into the gears and purges when you press load. Feed assist runs during prints. Multiplexing (several slots into one head) is in the planning stages.
Power Loss Recovery Working Resumes an interrupted print without homing Z into the part, and keeps the bed hot until you resume or discard it. Tested on a printer.

Milestones

  • Four MCU boards ported to Klipper and Kalico
  • Toolchanging and AFC standalone
  • Print start and stop sequences
  • Complete removal of firmwareExe
  • OpenCreator Updater (Pi-tunnel)
  • Real Zero Purge modes
  • Flow and VFA calibration without bugs on interrupted flow
  • GrumpyScreen macros and extruding
  • Installer verified end to end on a printer
  • RPi / SBC support out of testing
  • Working power loss recovery
  • ACE Pro with auto feed and auto load

Planned, not implemented as supported features

  • ACE Pro multiplexing: several ACE slots feeding one head (planning stages).
  • Sliced G-code 3MF intake in the print-upload path (SBC installs, not yet verified on a printer).
  • Version tracking
  • AI-vision overwatch for failures (Can be implemented via Pi and any service)
  • Further detection for print failures
  • Reducing amount of wasted filament when runout is occured

The installer works, and the OpenCreator Updater is being finished; see their rows in the table above.

Planned features aren't promised and may change or be dropped.